Hubbardton-forge 206440 Uživatelský manuál stáhnout pdf

HUBBARDTONFORGE.COM

-, -   

154 RT. 30 SOUTH

•

CASTLETON, VERMONT 05735

28808

Installation Instructions

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.

We hope you enjoy your xture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.

Please Note: This fixture is designed to be mounted on a standard

wall surface and may not be suitable for all applications. If installing in

a non-wood frame application, we recommend consulting a qualified

builder or electrician. Fixture should be mounted four feet above grade.

After installation extra hardware and accessories are possible; our kits

are used on multiple products and options

To Install Fixture (Figures 1 & 2)

Component Parts

A Fixture Front

B Slotted Screw

C Fixture Back

D Top Screw

E Mounting Bracket

F #8 Screw (4)

G #8 Countersunk Screw (2)

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

1. Carefully unpack the xture from the carton.

2. Loosen the slotted screw (B) in the bottom of the xture until

the xture front (A) is loose. Remove top screw (D) from top

of xture. Remove the xture front (A) from the xture back

Note: Fixture front (A) and screws (B&D) ship installed. Retain for

later use.

3. Center the mounting bracket (E) over the electrical box

being sure to hold it plum and level. With a pencil, mark the

location of all mounting holes in the wall mount bracket on

the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly

mounted electrical box and/or a framing member in at least two

locations. Do not depend on drywall anchors alone to support this

xture. If in doubt, contact a qualied electrician.

Put the mounting bracket down and drill 1/4" diameter holes

in the locations marked on the wall. For holes using

anchors, place the tapered end of the anchors (L) into the

holes and gently tap them ush to the wall using a light

weight hammer.

B296

Double Axis LED Sconce: 206440D

Page 1 of 4

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND

PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with

applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.

(Figure 1)

(Continued)

H Ground Screw

I Cupped Washer

J Driver

K Gasket

L Anchors (4)

M #10 Screws (4)

1 2 3 4

Installation Instructions 1

Shrnutí obsahu

Strany 1 - Installation Instructions

Strany 2

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Strany 3

Strany 4

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 206440 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 206440. Hubbardton Forge 206440 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 206440