Hubbardton-forge 306425 Uživatelský manuál stáhnout pdf

HUBBARDTONFORGE.COM

-, -   

154 RT. 30 SOUTH

•

CASTLETON, VERMONT 05735

30069

Installation Instructions

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.

We hope you enjoy your xture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.

Please Note: This fixture is designed to be mounted on a standard

wall surface and may not be suitable for all applications. If installing in

a non-wood frame application, we recommend consulting a qualified

builder or electrician. Fixture should be mounted four feet above grade.

After installation extra hardware and accessories are possible; our kits

are used on multiple products and options.

To Install Fixture (Figures 1 - 3)

Component Parts

A Fixture Front

B Slotted Screw

C Fixture Back

D Top Screw

E Mounting Bracket

F #8 Screw (4)

G #8 Countersunk Screw (2)

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

1. Carefully unpack the xture from the carton.

2. Loosen the slotted screw (B) in the bottom of the xture un-

til the xture front (A) comes loose from the xture back (C).

Remove top screw (D) from top of xture back (C). Remove

the xture front (A) from the xture back (C) (Figure 1).

Note: Fixture front (A) and screws (B&D) ship installed. Retain for

later use.

3. Center the mounting bracket (E) over the electrical box

being sure to hold it plum and level. With a pencil, mark the

location of all mounting holes in the wall mount bracket on

the wall behind.

Important: Wall mount bracket must be secured to a solidly

mounted electrical box and/or a framing member in at least two

locations. Do not depend on drywall anchors alone to support this

fixture. If in doubt, contact a qualified electrician.

Put the mounting bracket down and drill 1/4" diameter

holes in the locations marked on the wall. For holes using

anchors, place the tapered end of the anchors (L) into the

holes and gently tap them flush to the wall using a light

weight hammer.

B306

Double Axis LED Outdoor Sconce Large 306425D

Page 1 of 4

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND

PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with

applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.

(Figure 1)

(Continued)

H Ground Screw

I Cupped Washer

J Driver

K Gasket

L Anchors (8)

M #10 Screws (8)

N Caulking Lip

O Rubber Washers (3)

1 2 3 4

Installation Instructions 1

Shrnutí obsahu

Strany 1 - Installation Instructions

Strany 2

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Strany 3

Strany 4

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 306425 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 306425. Hubbardton Forge 306425 User Manual [en] Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 306425