Hubbardton-forge 161025 Uživatelský manuál stáhnout pdf

HUBBARDTONFORGE.COM

-, -   

154 RT. 30 SOUTH

•

CASTLETON, VERMONT 05735

27971 B

Installation Instructions

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.

We hope you enjoy your xture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.

To Install the Canopy (Figures 1,2 & 3)

Component Parts

A 8-32 Screw (2)

B Top Assembly

C Bottom Assembly

D Crossbar

E Ground Screw

F Cupped Washer

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

1. Carefully unpack the xture from the carton.

2. Remove two 8-32 screws (A) from top assembly (B) to sepa-

rate from bottom assembly (C). Place bottom assembly (C)

and two 8-32 screws (A) to the side for later use. (Figure 1)

3. Using two machine screws (not provided), fasten the cross-

bar (D) to the electric box. Crossbar is shipped attached to

canopy.

4. Note:A new electric box comes with screws. When replacing

a xture retain the existing screws for use with the

new xture.

5. Height of xture can be set before attaching the xture to

the ceiling. Remove screws w/lock washers (R) and canopy

plate (Q) from canopy (G). If height is going to stay at max

length or just a slight height adjustment is needed it may not

be necessary to remove the canopy plate.

Note:Fixture is shipped at max height.

6. Push supply/support cable (J) into canopy gripper (I) until

desired height is reached.

7. Coil supply/support cable (J) in canopy (G) and place

canopy plate (Q) in canopy (G). Install screws w/lock

washers (R) to secure plate.

CAUTION: BE SURE NOT TO PINCH THE SUPPLY/SUPPORT CABLE IN

BETWEEN THE CANOPY (G) AND THE CANOPY PLATE (Q).

A321

Airis Low Voltage Pendants 161020 & 161025

Page 1 of 4

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND

PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with

applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.

(Figure 2)

(Continued)

G Canopy

H #8 Screws

I Canopy Gripper

J Supply/Support Cable

Q Canopy Plate

R Screws w/Lock Washers

(Figure 1)

1 2 3 4

Installation Instructions 1

Shrnutí obsahu

Strany 1 - Installation Instructions

Strany 2

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Strany 3

Strany 4

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Příbuzné modely 161020

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 161025 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 161025. Hubbardton Forge 161025 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 161020

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 161025