Hubbardton-forge 308015 Uživatelský manuál stáhnout pdf

Installation Instructions B271

Ethos Sconce 308010D & 308015D Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

154 Route 30 South, Castleton, Vermont 05735

27720 A

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or

electrician.

To Mount Fixture to Wall (Figures 1 & 2)

Component Parts

A Fixture Assembly

B Wall Mount Bracket

C Anchors (4)

D #10 Screws (4)

E #8 Black Screws (2)

F Rubber Washer (2)

G Green Ground Screw

H Cupped Washer

I Caulking Lip

Caution: Be sure power is off at the main breaker

box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (B) over the

electrical box being sure to hold it plum and

level. With a pencil, mark the location of all

mounting holes in the wall mount bracket on

the wall behind.

IMPORTANT: Wall mount bracket must be

secured to a solidly mounted electrical box and/or a framing member in at least two locations. Do not

depend on drywall anchors alone to support this fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using

anchors, place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using

a light weight hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the

bracket into position. Using two machine screws (not provided), fasten the wall mount bracket (B) to the

electric box making sure that the bracket is level. Using the #10 screws (D), screw the bracket securely to

the wall. Be careful not to over-tighten or strip the anchors.

NOTE: A new electrical box comes with screws. When replacing a fixture, retain the existing screws for

use with the new fixture.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not

provided), connect fixture wires to supply wires (white to white or ribbed and black to black or smooth).

Ground the mounting bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail

lead to the bracket and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

1 2

Shrnutí obsahu

Strany 1 - 27720 A

Installation Instructions B271 Ethos Sconce 308010D & 308015D Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories 154 Rou

Strany 2 - 27720 A

Installation Instructions B271 Ethos Sconce 308010D & 308015D Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories 154 Rou

Příbuzné modely 308010

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 308015 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 308015. Hubbardton Forge 308015 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 308010

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 308015