Hubbardton-forge 18870 Uživatelský manuál stáhnout pdf

HUBBARDTONFORGE.COM

-, -   

154 RT. 30 SOUTH

•

CASTLETON, VERMONT 05735

30438

Assembly & Installation Instructions

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.

We hope you enjoy your xture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.

Note: After installation extra hardware and accessories are possible due

to our kits are used on multiple products and options.

To Complete Fixture Assembly (Figures 1 & 2)

Component Parts

A Fixture

B Fixture Pipe

C Canopy

D Crossbar

E Ground Screw

F Threaded Stud (2)

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

1. Carefully unpack the xture from the carton and thread

x ture pipe (B) over xture (A) wires.

2. Apply a drop of the supplied thread locking compound to

the internal threads of the xture (A) and screw xture pipe

(B) into xture (A), being careful not to twist the wires.

Note: After installation extra hardware and accessories are possible

due to our kits are used on multiple products and options.

3. Thread the wires from the xture pipe (A) into and through

the canopy pipe (H) up through the canopy (C).

4. Unscrew the clutch (J) from the canopy pipe (H); slide it

across the wires and onto the xture pipe (B). Follow this

with the plastic clutch sleeve (I), oriented so the tapered end

of the clutch sleeve nests in the clutch.

5. Slide the canopy pipe (H) as far as necessary to give you

the total length of the xture which you desire. Be

carful not to scratch the pipe surfaces and to pull excess

wire up through the canopy pipe (H). Screw clutch

(J) onto canopy pipe (H). There must be a minimum 1-1/2"

of inner pipe inside the outer pipe. Hand-tighten the

clutch to temporarily hold this adjustment. The clutch is not

securely fastened at this point; do not depend on it to hold

the xture. Important: To ensure full connection strength,

be sure the tapered end of the plastic clutch sleeve (I)

A357

Pluto Pendant 18870

Page 1 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND

PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with

applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.

(Figure 1)

(Continued)

G Knurled Ball (2)

H Canopy Pipe

I Plastic Clutch Sleeve

J Clutch

K Set Screw

1 2 3

Pluto Pendant 18870 1

Shrnutí obsahu

Strany 1 - Pluto Pendant 18870

Strany 2

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Strany 3

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 18870 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 18870. Hubbardton Forge 18870 User Manual [en] Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 18870