Hubbardton-forge 344935 Uživatelský manuál stáhnout pdf

Assembly & Installation Instructions G11

For Post-Mounted 34-4935 Page 1 of 4

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22748

Note: Fixture, Post and Cover Cap each sold separately.

To Install

Component Parts

A J Bolt (4)

B Post

C Flat Washer (4)

D Split Washer (4)

E Hex Nut (4)

F Cover Cap (Optional)

G Set Screw

H Fixture

J Fixture Cover

Caution: Be sure power is off at the main breaker box prior to installation.

Site Preparation

1. Run appropriate wiring to the site of the fixture, leaving enough excess wire

to reach the top of the post, plus 12 inches.

2. Pour flat and level concrete base with wiring emerging at the center. Insert J

bolts (A) so approximately 1" of the bolts are exposed above the concrete.

Position J bolts according to the template on the last page of these

instructions. Allow concrete to cure before installing fixture.

Installation

Note: Post may be cut to desired height before installation.

1. Position post over J bolts allowing supply wire to run up though the post

and secure using flat washers (C), split washers (D) and hex nuts (E).

2. Place cover cap (sold separately) (F) over post to conceal mounting

hardware.

3. Slip fixture cover (J) over post and lower until it sits on top of the cover cap

(F). Leave fixture cover in this location for now.

4. Connect fixture wires to supply wires using appropriate wire connectors

(not provided), black to black, white to white and bare copper or green to

bare copper or green. If fixture is wired with twin lead lamp cord, connect

smooth side of fixture wire to black, and ridged side to white.

5. Place fixture (H) onto post carefully tucking all wiring down into post and

making sure no wires are pinched between the post and the fixture. Secure with

set screw (G).

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

1 2 3 4

Shrnutí obsahu

Strany 1 - To Install

Assembly & Installation Instructions G11 For Post-Mounted 34-4935 Page 1 of 4 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Strany 2

Assembly & Installation Instructions G11 For Post-Mounted 34-4935 Page 2 of 4 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Strany 3 - (continued)

Assembly & Installation Instructions G11 For Post-Mounted 34-4935 Page 3 of 4 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Strany 4

Assembly & Installation Instructions G11 For Post-Mounted 34-4935 Page 4 of 4 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 344935 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 344935. Hubbardton Forge 344935 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 344935