Hubbardton-forge 307715 Uživatelský manuál stáhnout pdf

Installation Instructions B254

Erlenmeyer Outdoor Sconce 30-7710 & 307715 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

154 Route 30 South, Castleton, Vermont 05735

26975

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall

(Figures 1 & 2)

Component Parts

A Fixture Assembly

B Wall Mount Bracket

C Anchors (4)

D #10 Screws (4)

E #8 Black Screws (4)

F Rubber Washer (2)

G Green Ground Screw

H Cupped Washer

I Caulking Lip

Caution: Be sure power is off at the main

breaker box prior to installation.

1. Carefully unpack the fixture from the

carton.

2. Center the wall mount bracket (B) over

the electrical box being sure to hold it

plum and level. With a pencil, mark the

location of all mounting holes in the wall

mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must

be secured to a solidly mounted electrical box and/or a framing member in at

least two locations. Do not depend on drywall anchors alone to support this

fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked

on the wall. For holes using anchors, place the tapered end of the anchors (C)

into the holes and gently tap them flush to the wall using a light weight

hammer.

3. Thread the wires in the electrical box through the center hole in the wall

mount bracket while moving the bracket into position. Using the #10 screws

(D), screw the bracket securely to the wall. Be careful not to over-tighten or

strip the anchors.

4. Hold the fixture assembly (A) close to the wall mount bracket and using

suitable wire connectors (not provided), connect fixture wires to supply wires

(white to white or ribbed and black to black or smooth). Ground the mounting

bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail

lead to the bracket and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

5. Apply a generous bead of a suitable caulking material (not provided) to calking lip (I) on the fixture (Figure 2).

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 2)

(Figure 1)

1 2

B254 1
26975 1

Shrnutí obsahu

Strany 1 - 26975

Installation Instructions B254 Erlenmeyer Outdoor Sconce 30-7710 & 307715 Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories 15

Strany 2

Installation Instructions B254 Erlenmeyer Outdoor Sconce 30-7710 & 307715 Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories 15

Příbuzné modely 307710

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 307715 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 307715. Hubbardton Forge 307715 User Manual [en] [es] [fr] Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 307710

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 307715