Hubbardton-forge 307861 Uživatelský manuál stáhnout pdf

Installation Instructions B142

For Medium and Large After Hours Outdoor 30-7860, 30-7860F, 30-7861 & 30-7861F Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21193

To Adjust Top Plate

(Figure 1)

Component Parts

A 8-32 x 1/4" Screw Top Plate

B Top Plate

C Glass

D Bracket

E 8-32 x 3/8” Screw (2)

F Fixture

1. Carefully unpack the fixture from the carton.

2. Slide glass (C) into fixture (F).

3. Slip top plate (B) onto fixture (F) until it rests on top of glass (C).

4. Loosen screws in bracket (D).

5. Remove screw (A) from bracket (D) and set aside for later use.

6. Raise or lower bracket (D) as needed until it touches top plate (B) and tighten

screw (E).

7. Slip 8-32 x 1/4" screw (A) through top plate (B) and thread in to bracket (D) and

tighten (be careful not to over tighten).

8. Remove screw (A), top plate (B) and glass (C) and set to the side temporarily.

9. Continue with installation instructions below.

To Install Fixture to Wall

(Figures 2 & 3)

Component Parts

F Fixture

G Mounting Bracket

H 8-32 x 1” Screw (2)

I Caulking Lip

Caution: Be sure power is off at the main breaker box prior to installation.

1. Using two machine screws (not provided) attach mounting bracket (G) to the

electric box using inside oval holes to orient fixture.

Note: A new electric box

comes with screws. When replacing a fixture, retain the screws for use with

the new fixture.

2. Using suitable wire connectors (not provided), connect the fixture wires to the

supply wires, (white to white, black to black, bare copper or green to bare

copper or green). If the fixture is wired with twin lead lamp cord, connect the

ribbed side to white, and the smooth side to black.

Caution: Make sure wire

connectors are twisted on securely and no bare wires are exposed.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(Figure 2)

1 2

B142 1
21193 1

Shrnutí obsahu

Strany 1 - 21193

Installation Instructions B142 For Medium and Large After Hours Outdoor 30-7860, 30-7860F, 30-7861 & 30-7861F Page 1 of 2 Hand-Forged, Vermo

Strany 2

Installation Instructions B142 For Medium and Large After Hours Outdoor 30-7860, 30-7860F, 30-7861 & 30-7861F Page 2 of 2 Hand-Forged, Vermo

Příbuzné modely 307860

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 307861 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 307861. Hubbardton Forge 307861 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 307860

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 307861