Hubbardton-forge 137665 Uživatelský manuál stáhnout pdf

HUBBARDTONFORGE.COM

-, -   

154 RT. 30 SOUTH

•

CASTLETON, VERMONT 05735

27253 Rev D

Assembly & Installation Instructions

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.

We hope you enjoy your xture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.

Prepare the Canopy (Figure 1)

Component Parts

A Crossbar

B Jam Nut

C Threaded Nipple

D Canopy

E Canopy Ring

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

1. Thread jam nut (B) and crossbar (A) onto threaded nipple (C);

leave parts loose.

2. Using two machine screws (not provided), temporarily fasten

the crossbar (A) to the electric box.

Note: A new electric box comes with screws. When replacing a

xture, retain the existing screws for use with the new xture.

3. Adjust the length of threaded nipple (C) in crossbar (A) so

that canopy ring (E) will hold canopy (D) against the ceiling

with no threads showing for best appearance. When the

correct adjustment is established, tighten jam nuts (B)

against crossbar (A) to hold the adjustment.

4. Remove the crossbar and stem from the electrical box and

proceed with the assembly instructions.

Complete Assembly & Install Fixture (Figures 2 & 3)

Component Parts

A Crossbar

D Canopy

E Canopy Ring

F Canopy Pipe

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

1. Place canopy (D) over canopy pipe (F), followed by canopy

ring (E). Make sure smaller diameter side of canopy ring is

oriented up toward the canopy.

A311

Brindille Adjustable Pendant 137665

Page 1 of 4

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND

PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with

applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.

(Figure 1)

(Continued)

G Plastic Sleeve

H Clutch

I Set Screw

J Fixture Pipe



LARGER DIAMETER PIPE

TAPERED END OF

PLASTIC SLEEVE

(Figure 2)

1 2 3 4

Shrnutí obsahu

Strany 1 - PLASTIC SLEEVE

HUBBARDTONFORGE.COM-, -   154 RT. 30 SOUTH • CASTLETON, VERMONT 05735 27253 Rev DAssembly & Installatio

Strany 2 - 27253 Rev D

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Strany 3

Strany 4

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 137665 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 137665. Hubbardton Forge 137665 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 137665