Hubbardton-forge 138585 Uživatelský manuál stáhnout pdf

Assembly & Installation Instructions A257

For Aura Pendant 13-8585 Page 1 of 3

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

24787

To Install to Ceiling (Figures 1 thru 6)

Component Part

A Ceiling Bracket

B Lag Screw (4)

C Hex Nut

D Canopy

E Strain Relief

F Support Cable (3)

G Cable Gripper (3)

H Strain Relief Cap

I Supply wire

J Flat Head Screws (2)

K Threaded Standoffs (2)

L Cupped Washer

M Ground Screw

N Canopy Nipple

O Canopy Cover

P Lock Up

Caution: Be sure power is off at the main breaker box prior to

installation.

1. Carefully unpack the fixture from the carton.

2. Put the ceiling bracket (A) and canopy (D) together, making sure

the canopy mounting holes match up with the ceiling bracket

threaded standoffs. Orient them to achieve desired wire location.

Note: Canopy and ceiling bracket only install one direction which

determines where the wire entry location through the canopy

will be.

3. Using the four lag screws (B) attach ceiling bracket (A) to a

structural member in the ceiling, centering the

crossbar over the outlet box. We've supplied lag

screws with your fixture; however, different

materials and/or construction methods may

require different fasteners. If in doubt, contact a

qualified electrician. Do not

attach crossbar

directly to outlet box.

4. Install strain relief (E) into canopy (D). Thread

hex nut (C) onto strain relief and tighten

(Figure 2). Do not over-tighten.

5. Raise fixture and push support cable (F) next to

the strain relief (E) through cable gripper (G).

Slip canopy (D) onto the cable oriented so the

strain reliefs are above each other.

6. Slip the other two support cables (F) through the

canopy (D) and into the cable grippers (G) until

desired fixture height is accomplished and level.

7. Slip supply wire (I) through the strain relief cap

(H) and through the strain relief (E).

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(Figure 3)

(Figure 2)

1 2 3

A257 1
24787 1

Shrnutí obsahu

Strany 1 - 24787

Assembly & Installation Instructions A257 For Aura Pendant 13-8585 Page 1 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Strany 2

Assembly & Installation Instructions A257 For Aura Pendant 13-8585 Page 2 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Strany 3

Assembly & Installation Instructions A257 For Aura Pendant 13-8585 Page 3 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 138585 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 138585. Hubbardton Forge 138585 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 138585