Hubbardton-forge 137581 Uživatelský manuál stáhnout pdf

Installation Instructions A91

Large Bent Plane Pendant Page 1 of 3

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 19403

Stem Assembly (Figure 1)

Component Parts

A Fixture Pipe

B Fixture

1. Carefully unpack the fixture from the carton.

2. Carefully thread fixture pipe (A), threaded end first, over fixture wires.

3. Apply a drop of the supplied thread locking compound to the internal threads at

the top of the fixture (B) and screw stem into fixture, being careful not to twist

the wires.

Note: Application of the thread locking compound is necessary to prevent the

stem from loosening during regular maintenance and cleaning of the fixture. Be

certain to apply the compound.

4. See instructions below to complete the installation.

(Figure 1)

Complete Assembly & Install Fixture (Figure 2 below, Figures 3 & 4, next page)

Component Parts

A Crossbar

B Threaded Stud (2)

C Hanger Plate

D Lag Screw (4)

E 1/4-20 Nut (2)

F Canopy

G Clutch (2)

H Knurl Ball (2)

I Canopy Pipe

J Plastic Clutch Sleeve

K Fixture Pipe

Caution: Be sure power is off at the main breaker box prior to installation.

1. Thread the wires from the fixture pipe (K) into and through

the canopy pipe (I) up through the canopy (F).

2. Unscrew the clutch (G) from the fixture pipe (K), slide it

across the wires and onto the canopy pipe (I). Follow this

with the plastic clutch sleeve (J), oriented so the tapered end

of the clutch sleeve nests in the clutch.

3. Slide the canopy pipe (I) as far as necessary to give you the

total length of the fixture which you desire. Be careful not to

scratch the pipe surfaces and to pull excess wire up through

the canopy (F). There must be a minimum 1-1/2" of inner

pipe inside the outer pipe. Hand-tighten the clutch to

temporarily hold this adjustment. The clutch is not securely

fastened at this point; do not depend on it to hold the fixture.

Important: To ensure full connection strength, be sure the tapered end of the plastic clutch sleeve is oriented toward the

clutch when assembled (Figure 2).

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 2)

1 2 3

A91 1
19403 2

Shrnutí obsahu

Strany 1 - A91

Installation Instructions A91 Large Bent Plane Pendant Page 1 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route 3

Strany 2 - 19403

Installation Instructions A91 Large Bent Plane Pendant Page 2 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route 3

Strany 3

Installation Instructions A91 Large Bent Plane Pendant Page 3 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route 3

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 137581 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 137581. Hubbardton Forge 137581 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 137581