Hubbardton-forge 305710 Uživatelský manuál stáhnout pdf

Installation Instructions B277

Modern Prairie Outdoor Sconces 30-5705 & 30-5710 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

154 Route 30 South, Castleton, Vermont 05735

27899

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figures 1 & 2)

Component Parts

A Fixture Assembly

B Wall Mounting Bracket

C Anchors (4)

D #10 Screws (4)

E #8 Black Screws (2)

F Rubber Washer (1)

G Green Ground Screw

H Cupped Washer

I Caulking Lip

Caution: Be sure power is off at the main breaker box

prior to installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (B) over the electrical box being sure to hold it

plum and level. With a pencil, mark the location of all mounting holes in the wall

mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical

box and/or a framing member in at least two locations. Do not depend on drywall

anchors alone to support this fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on

the wall. For holes using anchors, place the tapered end of the anchors (C) into the

holes and gently tap them flush to the wall using a light weight hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount

bracket while moving the bracket into position. Using the #10 screws (D), screw

the bracket securely to the wall. Be careful not to over-tighten or strip the anchors.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable

wire connectors (not provided), connect fixture wires to supply wires (white to

white or ribbed and black to black or smooth). Ground the mounting bracket using

the green ground screw (G) and cupped washer (H) to secure a pigtail lead to the

bracket and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

5. Apply a generous bead of a suitable caulking material (not provided) to calking lip (I) on the fixture. Caulk should

be applied around the entire perimeter of the canopy. (Figure 2)

6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture firmly

onto bracket (B) and fasten with #8 black screw (E) and rubber washer (F) on top.

7. Install 2

black screw (E) in bottom of fixture attaching to wall mounting bracket (B).

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(Figure 2)

1 2

B277 1
27899 1

Shrnutí obsahu

Strany 1 - 27899

Installation Instructions B277 Modern Prairie Outdoor Sconces 30-5705 & 30-5710 Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accesso

Strany 2

Installation Instructions B277 Modern Prairie Outdoor Sconces 30-5705 & 30-5710 Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accesso

Příbuzné modely 305705

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 305710 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 305710. Hubbardton Forge 305710 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 305705

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 305710