Hubbardton-forge 207805 Uživatelský manuál stáhnout pdf

Assembly & Installation Instructions B265

Ondrian Wall Sconce 20-7801 & 20-7805 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

154 Route 30 South, Castleton, Vermont 05735

27214 B

Figure 1

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Wall Mounting Bracket D Electric Box Cover (for 4” Outlet box)

B Anchors (2) E # 8 Black Screw (3)

C #10 Screws (2) F Fixture Assembly

Caution: Be sure power is off at the main breaker box prior to

installation.

1. Carefully unpack the fixture from the carton.

2. Place the wall mounting bracket (A) over the electrical box using one

of the wiring holes provided being sure to hold it plum and level. If

using a single gang outlet box electric box, cover (D) is not needed.

Remove #8 black screw (E) from electric box cover (D) and save for

later use. Determine which electric box cover (D) location works the

best and attach to wall mounting bracket (A). With a pencil, mark the

location of all mounting holes in the wall mount bracket on the wall

behind.

IMPORTANT: Wall mounting bracket must be secured to a solidly

mounted to a framing member in at least two locations. Do not depend

on drywall anchors alone to support this fixture. If in doubt, contact a

qualified electrician.

Drill 1/4" holes in the locations marked on the wall. For holes using

anchors, place the tapered end of the anchors (B) into the holes and gently

tap them flush to the wall using a light weight hammer.

3. Thread the wires in the electrical box through the hole in the wall mounting bracket (A) while moving the bracket

into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or

strip the anchors.

4. Hold the fixture assembly (F) close to the wall mounting bracket (A) and using suitable wire connectors (not

provided) connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare

copper or green). Ground the mounting bracket using the green ground wire fastened to the back of the fixture

assembly (F).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

5. Carefully tuck all wires behind the fixture assembly (F) and inside the wall mounting bracket (A) and place the

fixture over the bracket so the holes in the top and bottom match the threaded holes in the wall mounting bracket

(A). Secure the fixture by threading the #8 black screws (E) through the holes in the fixture assembly (F) and into

the wall mounting bracket (B).

6. Install G-9 light bulbs (included)

Note: The bulb included is based on our design preference; see the fixtures wattage sticker for Max wattage

information.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

1 2

27214 B 1

Shrnutí obsahu

Strany 1 - 27214 B

Assembly & Installation Instructions B265 Ondrian Wall Sconce 20-7801 & 20-7805 Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Acc

Strany 2

Assembly & Installation Instructions B265 Ondrian Wall Sconce 20-7801 & 20-7805 Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Acc

Příbuzné modely 207801

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 207805 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 207805. Hubbardton Forge 207805 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 207801

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 207805