Hubbardton-forge 19415612HG Uživatelský manuál stáhnout pdf

Assembly & Installation Instructions A238

For Ribbon Chandelier 19-415612HG Page 1 of 3 _

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

24409

Install the Canopy (Figure 1)

Component Parts

A Crossbar

B Threaded Nipple

C Lag Screw (2)

D Lock Nut

E Canopy

F Loop Collar

G Threaded Loop

H Chain

I Fixture Loop

J Ground Screw

K Cupped Washer

L Hex Nut

Caution: Be sure power is off at the main breaker box prior to installation.

Caution: This fixture must be supported independently of an outlet

box. Crossbar is designed to fit in the bottom of a standard metal 4”

octagonal outlet box.

1. Drill two holes through the back of the outlet box and using

two lag screws (C) attach cross bar (A) to a structural

member in the ceiling, centering the crossbar in the outlet

box. We've supplied lag screws with your fixture; however,

different materials and/or construction methods may require

different fasteners. If in doubt, contact a qualified

electrician.

2. Thread the nipple (B) into the crossbar (A).

3. Thread lock nut (D) and threaded loop (G) onto nipple, then

place canopy (E) over threaded loop and adjust nipple

length to ensure a snug canopy fit. Once the length is

determined, set the canopy aside and lock nipple position

by tightening the locknut (D) against the crossbar (A).

4. Attach one end of the chain (H) to the fixture loop (I).

5. Attach the other end of the chain to the threaded loop (G)

and thread the fixture wires through every other link of the

chain (H) and up through the threaded loop (G) and nipple

(B) into the outlet box.

6. Using suitable wire connectors (not provided), connect

fixture wires to supply wires (white or ribbed side of fixture

cord to white supply, black or smooth side of fixture cord to

black supply, and bare copper to bare copper or green

supply). Ground the crossbar (A) using the ground screw

(J), cupped washer (K) and hex nut (L) to secure a pigtail

lead to the crossbar. Push wires back into outlet box.

Caution: Make sure wire connectors are twisted on

securely, and no bare wire is exposed.

7. Slide the canopy up the chain and over the threaded loop (G), securing

with loop collar (F). Make sure no wires are pinched between the canopy

(E) and the ceiling or crossbar (A).

(continued)

(Figure 1)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

1 2 3

Shrnutí obsahu

Strany 1 - Page 1 of 3 _

Assembly & Installation Instructions A238 For Ribbon Chandelier 19-415612HG Page 1 of 3 _ Hand-Forged, Vermont-Made Lighting and Accessor

Strany 2 - Page 2 of 3 _

Assembly & Installation Instructions A238 For Ribbon Chandelier 19-415612HG Page 2 of 3 _ Hand-Forged, Vermont-Made Lighting and Accessor

Strany 3 - Page 3 of 3 _

Assembly & Installation Instructions A238 For Ribbon Chandelier 19-415612HG Page 3 of 3 _ Hand-Forged, Vermont-Made Lighting and Accessor

Komentáře k této Příručce

Žádné komentáře

Hubbardton-forge 19415612HG Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Osvětlení Hubbardton-forge 19415612HG. Hubbardton Forge 19415612HG User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Osvětlení Hubbardton-forge 19415612HG